2009-2013 Cummins 8" BDS Long Arm Lift Kit (BDS632H)
Take your 4th Gen Cummins to the next level of stance and control of a 4-Link Long-arm suspension while sending it off to the moon with a full 8" of an increased ride height! This suspension system features 8" progressive Pro-Ride Coil Springs and solid steel upper long arms and thick tubular lower long control arms. The long control arm reduces caster change through wheel travel creating a more controlled feeling in the steering wheel both on and off-road.
Tire & Wheel Combinations:
- 38" x 14.0" w/ 17 x 9 and 4.5"
Notes:
- Measure rear axle tube before ordering. Some 4" axle models with dual overloads will require 406
- Rear lift options will not fit dually applications.
- If driveline vibration occurs, order either transfer case drop or indexing kit available in optional accessories. NOTE: 122606 transfer case drop kit will only replace the OE bracket #52121938AA
- 102009 Rear brake lines will not fit 2012-2013 models.
- Additional front driveline modification may be required.
- Exhaust modification will be required for dual rear shock kit 12200
- Will not fit Cab and Chassis models
Installation:
- Click Here For Installation Instructions
- Difficulty: 3 (where 1 = easiest and 5 = complicated)
Part Number: BDS632H
8" Front Coil Springs
Show more
8" Long Arm Box Kit
This Box Kit includes the following products:
- Pitman Arm
- 2 Bolt Packs
- Track Bar Bracket
- Sway Bar Link
- 2 Bump Stop Brackets
- 2 Urethane Bump Stops
- Driver & Passenger Side Brakeline Adaptor
- 2 Steering Stops - Weld On
- 2 Sway Bar Link U-Brackets
- 2 5/8” ID Hourglass Bushings
- 2 3/4” ID Wide Hourglass Bushings
- 2 .625 x .109 x 1.375 Sleeves
- 2 .750 x .090 x 1.575 Sleeves
- Bolt Pack - Sway Bar Hardware
- Bolt Pack - Misc. Hardware
- Bolt Pack - Bumper Spacer
- Rear Brakeline Bracket
Show more
Control Arm Box Kit
This Box Kit includes the following products:
- Driver & Passenger Side Upper Control Arms
- 2 Lower Control Arms
- 8 UCA Bushings - 3/4” ID
- 4 LCA Bushings - Axle
- 4 LCA Bushings - Frame
- 4 UCA Sleeves .750 x .095 x 2.33
- 2 LCA Sleeves 1.00 x .1875 x 2.60
- 2 LCA Sleeves 1.00 x 5/32 x 2.60 2010+ only (18mm ID)
- 2 LCA Sleeves 1.00 x .120 x 3.25
- 8 90 Degree Grease Zerks
Show more
Control Arm Mounts
This Box Kit includes the following products:
- Driver & Passenger Side Long Arm Bracket
- Bolt Pack
Show more
6-Bolt Indexing Ring Kit
Show more
5" Rear Block Kit w/ 4" Axle
Show more
5" Universal Lift Blocks w/ 3.5" Axle
Features:
- Blocks are made of cast iron for strength
- Tapered for correct pinion angle
- Sold in pairs
- Black powder coating
Show more
5" Lift Leaf Spring w/ 3.5" & 4" Axle (2x)
- Please select correct U-Bolts if you choose full Leaf Spring Replacements
Show more
Important: Measure your rear axle & select the appropriate kit.
U-Bolts - (3.5"X14.5") (4x)
Show more
U-Bolts - (3.5"X12.5") (4x)
Show more
U-Bolts - (4"X12.5") (4x)
Show more
NX2 Series Shocks (2x)
The BDS NX2 series gas shocks offer impressive performance on and off-road. Standard in most BDS lift kits, these nitrogen-charged, twin-tube shocks offer 10-stage velocity-sensitive valving for lightning-fast damper performance and control.
Show more
NX2 Series Dual Shocks (4x)
Show more
Fox 2.0 Series Shocks (2x)
Improve ride quality and capability with the FOX 2.0 performance series IFP shocks. Specially designed for BDS lift systems, these FOX 2.0 aluminum body shocks offer improved cooling capacity and corrosion protection. These shocks use race-proven vehicle-specific valving along with an internal floating piston (IFP) monotube design to separate the shock oil from high-pressure nitrogen to eliminate aeration and maximize performance on/off-road.
Show more
Fox 2.0 Series Dual Shocks (4x)
Show more
Required if you have selected Dual Shocks.
No Thanks
Dual Auxiliary Shock Mounting Bracket
Show more
NX2 Series Single | Dual Shocks
Important: These Shocks are for Single & Dual Rear, please selected the appropriate quantity.
The BDS NX2 series gas shocks offer impressive performance on and off-road. Standard in most BDS lift kits, these nitrogen-charged, twin-tube shocks offer 10-stage velocity-sensitive valving for lightning-fast damper performance and control.
Note:
- Will not fit 2013 models
- Exhaust modification on diesel models will be required.
Show more
Required if you have selected Dual Shocks.
No Thanks
Dual Shock Mount Kit
Show more
IMPORTANT: Upgrading to our sway bar disconnect kit will change the installation process for this system. Installation changes are clearly outlined in the instructions
Note:
- Works with 3-8" of lift
- Not for use with any other sway bar relocation brackets. The sway bar needs to be mounted in stock location on the frame.
- Will not work with 03-08 BDS 8" kits that have the sway bar relocation brackets at the axle or any other kit that does not have the factory axle mount bracket intact
- Inverted 'T' steering found on 08.5+ trucks is high recommended for steering-to-sway bar link clearance on 03-08 trucks. Do not vary from shock length listings. Max extended length is 25-1/4" for 3" lift, 30" extended for 8" lift
No Thanks
Sway Bar Disconnect Kit
Show more
No Thanks
Required if you have selected Dual Steering Stabilizers.
No Thanks
Dual Steering Stabilizer Bracket Kit
Show more
No Thanks
Universal Recoil Traction Bar
Show more
Standard Series Traction Bar - (3.5" Axle)
Reduce rear pinion angle change commonly referred to as axle wrap during acceleration with these BDS heavy-duty traction bars. Tubular design for good looks as well as serious axle control.
Show more
Standard Series Traction Bar - (4" Axle)
Show more
Required if you have selected the Recoil Traction Bar.
Note:
- Bracket kits are vehicle specific. The frame brackets install by drilling mounting holes for the brackets while the axle brackets install using a set of u-bolts. The traction bars and mounting brackets use a durable gloss black powder coat finish.
No Thanks
Recoil Traction Bar Mounting Kit - (4" Axle/SRW)
Show more
Features:
- Kevlar lined Stainless Steel Braided Brake Lines
- Virtually no volumetric expansion Firmer brake pedal feel with less pedal effort.
- Hose assemblies comply with D.O.T. Federal regulations (MVSS-106) Legal for street use in all 50 States.
- Teflon inner core (chemically inert) Approved for use with all brake fluids, including D.O.T. 5 Silicone.
- Resists moisture, Very flexible.
- Five-layer construction Rugged construction that resists road shock and hazards.
- Higher fitting pull-off than other D.O.T. assemblies.
- Standard SAE female fittings and ends Utilize standard brake fittings and hardware.
- PN# 102009 - Will NOT work on 2012+ trucks.
No Thanks
31" Front Brake Line
Show more
Features:
- Kevlar lined Stainless Steel Braided Brake Lines
- Virtually no volumetric expansion Firmer brake pedal feel with less pedal effort.
- Hose assemblies comply with D.O.T. Federal regulations (MVSS-106) Legal for street use in all 50 States.
- Teflon inner core (chemically inert) Approved for use with all brake fluids, including D.O.T. 5 Silicone.
- Resists moisture, Very flexible.
- Five-layer construction Rugged construction that resists road shock and hazards.
- Higher fitting pull-off than other D.O.T. assemblies.
- Standard SAE female fittings and ends Utilize standard brake fittings and hardware.
- PN# 102009 - Will NOT work on 2012+ trucks.
No Thanks
21" Rear Brake Line
Show more
No Thanks
Carrier Bearing Drop Kit
Show more