1994-1998 Cummins 500-600HP Power Package
If you are looking to make 500-600HP, this is the kit that will take you there!
Fleece Cheetah 63mm FMW Turbocharger
Features:
- Drop-in replacement turbo
- Capable of supporting vehicle modifications up to 650 RWHP
- Fleece Performance Exclusive FMW Compressor Wheel Technology.
- Inconel turbine wheel
- Lowers EGT's
- Stock-like spooling
Show more
Smeding Billet S363 Drop In Turbocharger
- Drop-in replacement
- Handles mild/moderate fueling upgrades
- Comes with an extended tip 63mm billet 6 blade compressor wheel
- Supports 600 HP
- Wastegate can be adjusted
- Includes T3 gasket and oil drain gasket
Show more
Pusher Low Mount Compound Turbocharger System
Note:
- Atmospheric Turbo is sold separately.
Features:
- Supports up to 750HP with stock Holset charger and over 1000HP with upgraded chargers
- CNC machined and laser-cut flanges
- Fully TIG welded with precise settings
- Designed to work with stock and most "stock replacement" aftermarket exhaust manifolds
- Front mount 5" Cold Air Intake
- Two-piece downpipe
Show more
Dynomite Stage 3 Injector Set
Features:
- Recommend timing 20°-22°
- Sold as Brand New Set - No Core
- Supports up to 700-750RWHP
- The largest injector set recommended for frequent street use
- Modified P-Pump and upgraded turbo(s) are required.
Show more
BD Fuel Control Plate
Features:
- Commonly known as a "cam plate"
- Controls the rack travel which affects the amount of fuel the P7100 fuel pump delivers
- Six different ramp designs
- Power gains from 30 to 150 hp and 70 to 300 lb.-ft. of torque
- Calibrated boost tube orifice improves turbo performance
- Strong knowledge of the P7100 pump is required for installation
Show more
BD 3000RPM Governor Spring Kit
- Designed and engineered to enhance the middle and high-end throttle response and enable more power thru the entire throttle range
- Only trained, qualified technicians with working knowledge of P7100 pumps should perform these upgrades
Show more
BD Delivery Valve Kit
- Increased flow without replacing plungers and barrels
- Only trained, qualified technicians with working knowledge of P7100 pumps should perform these upgrades
Show more
Fass 140GPH Titanium Lift Pump
Features:
- Power Rating: Stock - 700HP
- Preset Fuel Pressure: 45-47 PSI
- Flow Rating: 140GPH
- Filter Life Expectancy: 30,000 Miles
- Filtration Rating: 3 Micron
- Warranty: Limited Lifetime Warranty
Show more
No Thanks
Smeding HD 104lb Valve Springs
Features:
- 104lb Valve Springs
- Includes (24) Valve Springs
- Must-have for performance enthusiasts running 50PSI or greater
Show more
Hamilton Cams 103lb Valve Springs
- This is fine for a stock truck but as soon as you begin to make over 35psi (boost or drive pressure) at 3,800rpm the stock springs begin to lose control of your valvetrain.
- Triple Shot Peened & Stress Relieved
- 103lb Springs
- Handles Over 50PSI of Boost
- 180lb Nose Pressure
- Sold as a Set
Show more
No Thanks
Smeding Performance Push Rods
Heavy-Duty Pushrods:
- Push Rod Specs: 3/8" x .120 Wall.
- Don't settle for light-duty stock replacements that are only .083 wall thickness.
Extreme Heavy-Duty Push Rods:
- If you are over 750hp with your ISB, the cylinder pressures dictate that you step up to Smeding Diesel's extreme duty pushrods.
- Push Rod Specs: 3/8" x .120 wall intake pushrod and a 7/16" .120" exhaust pushrod.
Show more
Hamilton Cams Extreme Duty Pushrods
- Handles Over 750HP
- Stronger & More Reliable than OE
- Complete Set (varies on inventory levels at the time)
- 3/8".095 Wall Intake Pushrod & 7/16" .120 Exhaust Pushrod
- Or
- 12mm diameter .120" wall throughout
Show more