2017-2019 Powerstroke 6" 4-Link Lift Kit (BDS1527H)
Take your new Super Duty to the next level with the tried & true BDS 4-link conversion system. A big upgrade for your truck, these high-strength 4-link conversions offer improved handling, stability, strength, & caster control during wheel travel. In the rear of these 6" systems, BDS offers multiple lift options for both the OE 2-leaf main spring pack & OE 3-leaf main spring pack equipped trucks. With BDS NX2 Series shocks to compliment the front setup for all-around impressive performance.
Tire & Wheel Combinations:
- 38 x 13.50 w/ 17 x 9 and 4.5" - 5"
- 38 x 13.50 w/ 17 x 10 and 5"
- 38 x 13.50 w/ 20 x 10 and 5"
Notes:
- If equipped with a 2-piece rear driveshaft, a Carrier Bearing Drop Kit may be required (BDS123402)
- 38 x 13.50 tires may require minor trimming.
- Some models may be factory equipped with a 2-leaf main rear leaf spring pack and others a 3-leaf main. Be sure to order the correct option when customizing your kit.
- The transfer case indexing ring will not fit 6.2L vehicles equipped with the 6R100 transmission.
- If your truck is equipped with a factory rear sway bar add: 123808
- The indexing ring has not been designed to work on manual-shift transfer case models. Modification to the shift cable mount will be required.
- Diesel trucks ONLY.
- Although this is pictured with Fox Shocks, this kit will come equipped with BDS Shocks. If you would like fox shocks, please reach out.
- For trucks equipped with 2-Leaf main rear leaf pack only. Click here to view an example.
Installation:
- Click Here For Installation Instructions
- Difficulty: 4 (where 1 = easiest and 5 = complicated)
Part Number: BDS1527H
6" 4-Link Box Kit
This Box Kit includes the following products:
- Upper & Lower 4-Link Arms
- Bolt Pack - 4-link Arm Hardware
- Bag Kit - Upper & Lower Arm
- 4 90 degree grease fittings
- 4 1.0 x 0.120 x 3.25 DOM Sleeve
- 8 Bushings
- Cam Lock Plates
Show more
6" 4-Link Box Kit
This Box Kit includes the following products:
- Pitman Arm
- Front Bump Stop Extension
- Track Bar Bracket
- Driver & Passenger Side Sway Bar Drop
- Driver & Passenger Side 4-Link Bracket
- BDS Badge
- Rivet Bolt Packs
- Track Bar Cam Washer
- Driver & Passenger Side Front Brakeline Bracket ( 6" & 4" Box Kit)
- U-hardline extension (6" Box Kit)
- 4-Link Bracket Nut Tab
- M8-1.25 x 130mm Bolts
- 5/16" SAE Flat Washers
- Zip Ties
- Drive Shaft Boot Clamp
- 1/8" x 1-1/4" Cotter Pin
- Bolt Pack - 4-Link Bracket
- Bolt Pack - ABS Wire Clamp (4" Box Kit)
- Bolt Pack - Sway Bar Drop Bracket
Show more
6" Rear Block Kit
This Box Kit includes the following products:
- Driver & Passenger Side 5" Tapered Block
- 4 5/8 x 3-1/8 x 19 Semi-Round U-Bolts
- 1" x 3" Bolt-on Block
- Bag Kit
- 7/16" x 6" Center Pin
- 5/8" Washers
- 5/8" High Nuts
- E-Brake Relocation Bracket
- E-Brake Clamp Bracket
- Bolt Pack -E-Brake Brackets
Show more
SD Transfer-Case Indexing Kit- DSL
Show more
Note:
- Some F250/350 factory options increase the main leaf pack count from 2 to 3 leafs (this is for top overload options only). Be sure to verify which factory leaf spring configuration your vehicle has and choose the appropriate option below.
- If you have a factory 3-Leaf Main, you can skip this section.
No Thanks
5" Rear Block (2-Leaf)
Does the rear of your truck need a little extra boost? The BDS Add-a-Leaf kits are the perfect answer. This kit comes with complete instructions, new center pins, and new leaf alignment clamps. Order one kit per axle. Add-A-Leaf kits are sold as pairs except for dual add-a-leaf kits which are sold in sets of four.
U-bolts are not included in add-a-leaf purchases but are listed here for reference. The u-bolts listed may be longer than necessary for add-a-leaf installation. U-bolts sizes were based on maximum OE leaf packs which can vary widely due to towing packages, GVWR variations, etc.
Show more
4" Lift Rear Leaf Spring (2x)
Show more
Only select this box kit if you have added full leaf spring replacements.
No Thanks
6" Rear Leaf Spring Box Kit
Show more
Front NX2 Series Shocks (2x)
The BDS NX2 series gas shocks offer impressive performance on and off-road. Standard in most BDS lift kits, these nitrogen-charged, twin-tube shocks offer 10-stage velocity-sensitive valving for lightning-fast damper performance and control.
Show more
No Thanks
Features:
- Adjustable axle wrap control utilizing dual-stage resistance springs
- Full-floating traction bar design will not bind throughout the full range of wheel travel and/or hinder suspension articulation.
- Does not adversely affect ride quality when springs - particularly when resistance springs are adjusted to still be active.
- Spring preload can be adjusted on the vehicle without disassembling the traction bar
- Adjustments can be made for optimum performance over a wide range of uses/terrain. (On-Road - Unloaded, Towing/Hauling, Off-Road, Competition pulling)
- Traction bar ends are greaseable and rebuildable
No Thanks
Universal Recoil Traction Bar
Show more
Required if you have added the Traction Bar.
No Thanks
RECOIL Traction Bar Mounting Kit (3.5"- 4" Axle Diameter)
Mounting brackets are bolt-on, only requiring minor drilling for frame mount installation.
Note:
- Does not fit regular cab models
Show more
The kit comes with multiple shim plates for full adjustability from 1/8" to 1-1/2" of drop. Includes necessary hardware.
Note:
- For all 3"+ Lift Kits.
No Thanks
Carrier Bearing Drop Spacer
Show more
If your truck is equipped with a rear sway bar, these are recommended.
No Thanks
IMPORTANT: Will ONLY fit trucks with a 4 bolt flange style rear driveshaft mount on the axle.
When lifting the 2011-2020 model Ford Super Duty 6" or more it may be necessary to extend the rear driveshaft to ensure adequate spline engagement at full droop of the suspension. While one option is to have a custom extended length driveshaft built, BDS Suspension is now offering a more affordable solution with their new high strength rear driveshaft spacer. Built from T6061 billet aluminum and CNC machined for a precision fit, this rear driveshaft spacer mounts between the driveshaft and rear axle providing the necessary driveshaft spline engagement. Longer hardware and thread locker are also supplied to complete the simple installation.
No Thanks
The following kit ID's 1567H, 1567F, 1551H, 1551F - If installed on a truck with a top mount overload spring, and the overload spacer block is taller than 1-1/8" then these U-Bolts (Qty:4) are required.
Note:
- All u-bolts come with high nuts and washers.
No Thanks
Universal U-Bolt (4x)
Show more