2011-2016 Powerstroke 4" Lift Kit (BDS588H)
Centered around two ProRide Coil Springs. The box kit includes two new radius arm drop brackets to put the stock radius arm back at the factory angle which will maintain your stock driving characteristics; everything you need to properly lift your Powerstroke.
Tire & Wheel Combinations:
- 35" x 12.50" w/ 17 x 9 and 4.5"
- 35" x 12.50" w/ 18 x 9 and 4.5"
- 35" x 12.50" w/ 20 x 9 and 4.5"
Notes:
- Removal of factory block required. Rear add a leaf is required for models equipped with factory 3-7/8" block for a level to tail high stance. Single add-a-leaf kit # 113218 is recommended for a more level stance - Dual add-a-leaf kit # 113209 is recommended for tail high stance. (Add-a-leafs do not apply to rear leaf spring equipped systems)
- Front exhaust modification may be required to clear the front driveshaft (gas only).
- If equipped with a 2-piece driveshaft, a driveshaft alignment kit may be required.
- Although extremely rare, front and/or rear driveline vibration may occur.
- If equipped with a rear sway bar, #123009 is required.
- U-bolts will not work on dually.
Installation:
- Click Here For Installation Instructions
- Difficulty: 3 (where 1 = easiest and 5 = complicated)
Part Number: BDS588H
Base Kit
4" Front Coil Springs
Show more
Fox 2.5 Series Remote Reservoir Coilovers
The new coil-over conversion setup for the 2.5" & 4" lift heights utilizes the factory coil bucket and an included integrated upper and lower coil-over mount bracket system. The installation of the upper bracket requires minor modification to the factory coil mount. This system is now available as a stand-alone kit for those looking to upgrade an existing coil spring or spacer kit.
Show more
Fox 2.5 Series Remote Reservoir Coilovers w/ DSC
The new coil-over conversion setup for the 2.5" & 4" lift heights utilizes the factory coil bucket and an included integrated upper and lower coil-over mount bracket system. The installation of the upper bracket requires minor modification to the factory coil mount. This system is now available as a stand-alone kit for those looking to upgrade an existing coil spring or spacer kit.
Show more
Coilover Mounting Kit
Required if you have selected Coilovers as a front lift option.
No Thanks
Coilover Mounting Kit
Show more
Front Box Kit
4" Box Kit
This Box Kit includes the following products:
- 2 Radius Arm Drop Brackets
- 3 Bolt Packs
- Track Bar Bracket
- Track Bar Bracket Spacer
- 2 Cam Washers
- Driver & Passenger Side Sway Bar Drop Bracket - (4" & 6" Lift)
- Driver & Passenger Side Front Brakeline Bracket - (6" Lift)
- 2 8mm-1.25 x 130mm bolts
- 2 5/16" SAE Flat Washers
- Steering Stabilizer Brackets
- 2 Steel Stabilizer Spacers
- Bolt Pack - Stabilizers
- Pitman Arm
- Zip Ties
Show more
Rear Lift Option
5" Rear Block Kit w/ or w/o Overloads
Show more
3-4" Lift Leaf Spring (2x)
BDS Glide-Ride leaf springs will reduce axle wrap and create a more controlled and stable feel when towing. The actual leaf spring may not be exactly as shown in the photo. Includes OE-style bushings installed.
Note:
- BDS leaf springs are not intended for use beyond the truck's maximum payload capacity. Trucks equipped with overload springs will only have the capacity of a non-overload-equipped truck. If heavy payload use is desired, supplemental rear airbags are recommended.
Show more
Leaf Spring Box Kit
Required if you have selected full Leaf Spring Replacements.
No Thanks
Rear Leaf Spring Box Kit
Show more
Add A Leaf
IMPORTANT NOTE:
- If you chose "Rear Leaf Springs" during the Rear Lift Options selection, choose "No Rear Add-A-Leaf Kit" and continue to the next selection. This option only applies to "Rear Block Kit" equipped systems.
- When building your system with the "Rear Block Kit" option, models equipped with a factory 3-7/8" block require an optional add-a-leaf kit to achieve a level to tail high stance. On these models, we recommend adding a single add-a-leaf kit # 113218 for a more level stance - Dual add-a-leaf kit # 113209 is recommended for tail high stance.